ASTM A182 for Procurement Managers

Nov 05, 2026

Leave a message

Keywords : ASTM A182 procurement, A182 flange buying guide, F316L F22 F91 forging specification, A182 MTC inspection, A182 vs A105, duplex steel F51 F60 A182.

1. What Is ASTM A182?

ASTM A182 / A182M​ – Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service.

It covers forged/rolled pressure-piping components:

Pipe flanges

Forged fittings

Valve bodies and pressure-retaining parts

Components made to ASME B16.5, B16.11, B16.47, etc.

Material families:

Low-alloy steels: F11, F22, F91, F92

Ferritic / martensitic stainless

Austenitic stainless: F304/L, F316/L, F321, F347

Duplex / super duplex: F51, F60, F53, F55

Scope limit: max 10,000 lb (4,540 kg) per piece; larger parts use A336/A965.


2. Why Procurement Should Care

A182 defines metallurgical acceptability, not just shape. Wrong grade or missing heat treatment can cause:

Weld failure

SCC / pitting in chloride service

Creep rupture at high temperature

Rejection by TPI or ASME inspector


3. Grade Selection (Buyer's View)

Service

Typical Grade

Key Check

General corrosion

F304 / F316

Use L-grade for welding

High-temp steam / H₂

F11 / F22

Heat treatment + hardness

High-parameter power

F91 / F92

Grain size, UT, impact

Seawater / FGD

F51/F60, F53

Ferrite balance, solution anneal

Note: F60 (S32205) is tighter than F51 (S31803); many export projects prefer F60.


4. Procurement Pitfalls & Controls

4.1 Never specify only "A182"

Always state:

Standard + edition: ASTM A182/A182M-26a (or contract edition)

Grade: F316L, F22 Cl.3, F91…

Unit system: inch-lb or "M" (SI)

Dimensional standard + pressure class

❌ "A182 flange"

✅ "ASTM A182 F316L, WN Flange, ASME B16.5, CL300, RF"


4.2 Edition & Unit System

ASTM revises regularly (active edition check on astm.org)

Default is inch-pound unless "M" is ordered

Do not mix SI and inch-lb values


4.3 Heat Treatment Is Mandatory Info

Austenitic: solution anneal + rapid quench

Duplex: strict solution temp + quench

F91/F22: normalize + temper, with records

PO should require: heat treat lot no., furnace record, or equivalent.


4.4 MTC Review (EN 10204 3.1 / 3.2)

Verify:

Heat number matches marking

Chemistry within grade limits

Tensile / yield / elongation / RA / hardness

Duplex: ferrite content (ASTM A800/A799)

H-grades: grain size

HT record + NDT report (UT/MT/PT)

No heat-traceability = reject.


4.5 Supplementary Requirements Must Be Written

Not automatic unless specified:

UT (A388)

MT/PT

Charpy impact

IGC (A262)

TPI / EN 10204 3.2

If you don't write it, supplier may omit it.


4.6 Marking & Traceability

Each forging should show:

ASTM A182

Grade (F316L etc.)

Heat number

Manufacturer ID

Pressure class / standard for flanges

Receiving inspection: mark ↔ MTC ↔ PO must match.


4.7 Sour / H₂ / Cryogenic Service

H₂S → NACE MR0175 / ISO 15156 (hardness, S/P, HT)

Low temp → Charpy impact

Hydrogen service → F22 temper control + hardness cap


5. Purchase Order Snippet

Material: Forged component per ASTM A182/A182M-26a

Grade: F316L (or as specified)

Dimensions: ASME B16.5, NPS, Class_, RF

Heat treatment: Solution annealed + quench, record required

MTC: EN 10204 3.1 (3.2 with TPI if applicable)

NDT: UT per A388 + MT/PT where applicable

Marking: A182 / Grade / Heat No. / Mfr. mark

Supplements: impact / IGC / NACE only if specified


6. Bottom Line

With ASTM A182, you are buying a verified metallurgical condition-not just a forging shape.

Procurement checklist:

Lock grade + edition + dimensional standard

Write supplementary tests into the PO

Verify heat number, MTC, heat treatment, NDT on receipt


 

Send Inquiry